DEVI DEVIreg Touch Installation Guide

DEVIreg™ TouchElectronic Intelligent Timer ThermostatInstallation Guidewww.DEVI.comPLEASE DO NOT TRY TO ASSEMBLE THIS THERMOSTAT BEFORE FULLY READING

Follow the steps below to mount the thermostat:1. Open the thermostat:Important: Do NOT press on the display screen whenremoving the front part.(botto

The screen of the heating cable must be connected tothe earth conductor of the power supply cable by us-ing a separate connector.Note: Always instal

Initially it is recommended to leave the thermostat connectedto the main supply for 15 hours to fully charge the battery. The current time and day is

2. Press the hour numbersand use the < and > ar-rows to set the hour.Press to conrm.3. Press the minutes num-bers and use the < and >arr

6. On the SETUP informa-tion screen, press tostart.7. Use the < and > arrowsto select whether only afloor sensor or a combi-nation of room and

9. Use the < and > arrowsto select the ooringtype. Press to conrm.10. Use the < and > arrowsto select the room type.Press to conrm.11

12. Use the < and > arrowsto select whether thetimer should be activatedor not. Press to con-rm and end the initialthermostat setup. SkipStep

The forecast feature also optimises heating stop whenswitching from comfort temperature to economy tempera-ture.How to turn the forecast feature on an

3. Press FORECAST. Thenpress ON to optimiseheating start/stop or OFFto simply let the heatingstart/stop at the specifiedtime. Press to confirm. To

3. Press WINDOW OPEN.Then press ON to tempo-rarily turn off heating incase of a sudden temper-ature drop in the room orOFF to let the thermostatheat d

2. Press SETTINGS in thebottom right corner ofthe menu. Then press IN-STALLATION and MAN-UAL SETUP.3. Press MAX. FLOOR. Thenuse the < and > arro

If you break the small plasticseal on the back of the displaymodule, e.g. using a screw-driver, it will be possible to setture up to 45°. Furthermore,

Ther-malresist-ance[m2K/W]Examples of floor-ingDetails Approximatesetting for 25˚Cfloor tempera-ture0.05 8 mm HDF basedlaminate> 800kg/m328˚C0.10 1

4 SymbolsThe following symbols may appear in the upper left cornerof the temperature display:Sym-bolWhat it meansThe thermostat is in manual mode, i.e

5 Warranty5Y E A R6 Disposal InstructionDEVIreg™ Touch24 Installation Guide

DEVIreg™ TouchInstallation Guide 25

DEVIreg™ Touch26 Installation Guide

DEVIreg™ TouchDanfoss A/SElectric Heating SystemsUlvehavevej 617100 VejleDenmarkPhone: +45 7488 8500Fax: +45 7488 8501E-mail: [email protected]

DEVIreg Touch Design Frame140F1064Intelligent TimerThermostatFloor / Room Sensor220-240V~50-60Hz~0 to +30°C16A/3680W@230V~IP 21Product DocumentationDK

Table of Contents1 Introduction ... 31.1 Technical Specifications ... 41.2 Safety Instructions ... 72 Mounting Instructions ...

▪An installation wizard with room/floor type-specificsetup.▪Support for multiple frame systems.▪Compatible with several 3rd party NTC sensors.▪Thermos

Sensing units NTC 6.8 kOhm at 25°CNTC 10 kOhm at 25°CNTC 12 kOhm at 25°CNTC 15 kOhm at 25°C (Default)NTC 33 kOhm at 25°CNTC 47 kOhm at 25°CSensing val

Sensor failure moni-toringThe thermostat has a built-inmonitoring circuit, which willswitch off the heating if the sen-sor is disconnected or short-ci

1.2 Safety Instructionsbefore installation.IMPORTANT: When the thermostat is used to control ato determine suitable temperature settings (it isrestric

2 Mounting InstructionsPlease observe the following placement guidelines:Place the thermostat at a suitable height onthe wall (typically 80-170cm.).Th

Note: A oor sensor enables a more accuratetemperature control and is recommended inall oor heating applications and mandatoryunder wooden oors to r